Bearcat 980 SSB Bedienungshandbuch

Stöbern Sie online oder laden Sie Bedienungshandbuch nach Funkgeräte Bearcat 980 SSB herunter. Bearcat 980 SSB Owner`s manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken

Inhaltsverzeichnis

Seite 1 - Owner’s Manual

Owner’s ManualPrinted in VietnamU01UT563ZZZ(0)®980 SSB

Seite 2 - CONTENTS

E-10A short “loaded” whip antenna is easier to install on an automobile, but its efficiency is less than that of a full quarter-wave whip antenna. Con

Seite 3

E-112. Plug a 4-pin microphone connector into the 4-pin side of the adapter.MARINE INSTALLATION Consult your dealer for information regarding marine

Seite 4 - SAFETY NOTICE

E-12ALL CHANNEL SCANWhen All Channel Scan is on, the radio scans channels until it receives a signal. It moves to the next channel if it receives no s

Seite 5 - EMERGENCY OPERATION

E-134. Press MENU/OK to set Weather Scan mode to ON or turn the selec-tion knob until OFF displays and then press MENU/OK to set it. WXSCAN displays

Seite 6 - CONTROLS AND FUNCTIONS

E-14Clear Channels from Memory1. In MEM mode, select a channel.2. Press and hold MEM/SCAN until CLEAR displays.3. Release MEM/SCAN. The radio plays

Seite 7

E-15in that color. The available colors are:Option No:ColorOption No:Color1 Blue 5 Magenta2 Green 6 Yellow3 Cyan 7 White4 Red6. Press MENU/OK to sele

Seite 8 - 17 18 19

E-16Battery CheckCheck the DC power levels if you feel your radio is not performing properly.1. Once DIAG displays, press MENU/OK; VOLT displays.2.

Seite 9 - INSTALLATION

E-17displays. Press MENU/OK. The radio returns to the last operating mode and channel.OTHER FEATURESS/RF/CAL/SWR Meter You can check your incoming sig

Seite 10 - Negative Ground System

E-18To replace a blown fuse: 1. Press ends of the fuse holder together. Twist to open. Carefully separate the two pieces. 2. Remove the fuse and ins

Seite 11 - USING YOUR BEARCAT 980 SSB

E-19Problem SuggestionAntenna check returned FAIL.Make sure your antenna ground is good.Check for damage to the antenna.Check the SWRs at a CB shop. H

Seite 12

CONTENTSSAFETY NOTICE ... 4UNPACKING ...

Seite 13

E-20 RX: At no signal: 650 mAOperating Temperature: -22°F to 140°F (-30°C to 60°C)Accessories: DC Power Cord Noise Cancelling Microphone Micropho

Seite 14

E-21TWO-YEAR EXTENDED WARRANTY Important: Evidence of original purchase is required for warranty service. WARRANTOR: UNIDEN AMERICA CORPORATION (“Unid

Seite 15

E-22purchase and a note describing the defect that has caused you to return it. The Product should be shipped freight prepaid, by traceable means, to

Seite 16

E-23RADIO CODE DEFINITIONS The following list contains common “10-Codes” used by CB radio operators for faster communication and better understanding.

Seite 17 - MAINTENANCE

E-24Code Meaning Code Meaning10-24 Completed last assignment 10-81 Reserve hotel room for 10-25 Can you contact 10-82 Reserve room for 10-26 Disrega

Seite 18 - TROUBLESHOOTING

Uniden is a registered trademark of Uniden America Corporation.Bearcat is a registered trademark of Uniden America Corporation.Features, specications

Seite 19 - SPECIFICATIONS

E-4SAFETY NOTICEThe antenna used for this radio must be properly installed and maintained and must provide a separation distance of at least 59 cm (23

Seite 20

E-5UNPACKINGYour Bearcat 980 SSB contains the following:  Bearcat 980 SSB CB 2-way mobile radio  Microphone  Mounting Bracket Kit  DC Power Co

Seite 21 - TWO-YEAR EXTENDED WARRANTY

E-6All channels except Channel 9 may be used for normal communication. The FCC reserves Channel 9 for emergencies involving the immediate safety of in

Seite 22

E-7press and hold the PTT button and adjust the gain levels with the Channel Selector knob. (Levels 1 - 5). The LED will stay on for 5 seconds after a

Seite 23 - RADIO CODE DEFINITIONS

E-811. MEM/SCAN: Press to start or stop scanning modes [All Channel Scan (see page 12) and Memory Scan (see page 12)]. Press and hold to set or clear

Seite 24

E-9 When the external speaker is plugged in, the internal speaker is o.19. POWER +12 VDC: Connects DC power to transceiver. 20. FUSE 6A: Provides c

Kommentare zu diesen Handbüchern

Keine Kommentare